Close

• Manufacturer:
  Rayco
• Model:
  RG35

GENERAL
-Weight: 1830 Lbs Maximum
-Length: 114" Maximum (Arm in storage position)
-Height: 52" Maximum
-Width: 35" Maximum
-Width with Dual Wheels: 52.5" Maximum
-Chip Collection Capacity: 12.5 cu. Ft Minimum
-Chassis Design: Electrically welded 3" x 3" x 3/16" Square Steel Tubing, Formed 1/4" and 3/8" Gr. 80 steel
-Self-Propel Means: Self-propelled with variable speed control and automatic hill brake
-Operator Control Console: Controls mounted On Swing-away Arm with a Fully Covered Valve Bank
-Swing Pivot Bearings: 9" diameter slewing ring
-Brakes: Rear - Spring Applied Hydraulic Release
-Tires: 18 x 8.5-10 R4 4 ply
-Drive Axle Bearings: 1-1/2" flange roller minimum with grease fitting

ENGINE
-Model: Briggs & Stratton Vanguard 35hp Required
-Main Bearings: 2 Minimum
-Number of cylinders: 2
-Bore: 3.36"
-Stroke: 3.40"
-Displacement: 60.5 cu. In Minimum
-Maximum no load RPM: 3600
-Gross HP at maximum no load RPM: 35HP Minimum
-Maximum rated torque: 39.5ft lbs @2500 RPM Minimum
-Cooling medium: Unrestricted Air Flow Required
-Air Cleaner: Heavy Duty, Dual Element, Dry type
-Oil Filter: Spin-on type
-Fuel Tank Capacity: 6.5 gallons Minimum
-Electrical System: 12 volts/15 AMP Alternator Required

HYDRAULIC SYSTEM
-Pump Displacement: 0.62 cu. In. Minimum
-Pump Gallonage @ 3600 RPM: 5.2 GPM
-System Pressure Relief: 2500 PSI Aux / 3500 PSI Drive Minimum
-Oil Tank Capacity: 2 Gallons Minimum
-Oil Filter: 10-Micron Full Flow
-Oil Type: Tellus T46
-Valve: Spring-Centered Series
-Hose Capacity: 3000 PSI Working Pressure
-Swing Cylinder: Minimum 3" Bore, 6" Stroke, 1-1/4" Rod Minimum
-Lift Cylinder: Minimum 2.5" Bore, 8" Stroke, 1-1/4" Rod
-Hydraulic Wheel Drive Motor: 10.4 cu. In/rev
-Drive Chain: 50R Series Minimum
-Fittings: O-ring Required

CUTTING WHEEL
-Wheel Diameter: 17.25" Maximum
-Wheel Thickness: 1" Minimum
-Cutting Wheel Bearings: 1.5" Pillow Block Minimum
-RPM: 1170 Approximately
-Intermediate Belt: Banded "A" type 3-section V-belt
-Drive Chain: Gates Polychain GT, Low Maintenance
-Jackshaft Bearings: 1.5" Pillow Block Minimum
-Cutting Teeth: RAYCO Super tooth forged, One-piece, with tungsten carbide tips
-Cutter Teeth Quantity: 18 Maximum
-Belt Guard: Steel required
-Chip Retaining Curtains: Fabric impregnated rubber
-Cutter Wheel Engagement: Electromagnetic clutch with the "Quick Stop" brake system

CUTTING RANGE (without repositioning)
-Below Ground Level: 12" Minimum
-Above Ground Level: 24.5”Minimum
-Cutting Width: 51" Minimum
-Forward - Backward: Unlimited in Drive Mode

OPTIONS
-TRSJR Trailer
-Command Cut
-Dual Wheel Tires (Requires TRSJRW or TRSJRWB)
-Blade (option is for removal of standard blade)
-Pintle Hitch